A flow-meter upgrade will better support the natural gas flow heating of your processes.
Nearly all industrial processes and manufacturing operations rely on natural gas as a fuel, even if it is only for plant heating, ventilation and air conditioning (HVAC). However, heavy-duty industrial plant processes (Fig. 1), such as those found in manufacturing industries including steel and aluminum, depend heavily on natural gas to fuel the processes used in their production.
According to the U.S. Energy Information Agency (EIA), the United States consumed about 30.5 trillion cubic feet (TcF) of natural gas (or 31.5 quadrillion BTUs) in 2020. The primary uses of natural gas in the U.S. are for electricity generation and industrial heating, with 38% for electric power generation followed closely by 33% for use by industry, 15% for residential, 10% for commercial and 3% for transportation. Note that electric power’s share also includes the electricity consumed by industry.
According to the U.S. EIA, “The industrial sector uses natural gas as a fuel for process heating, in combined heat and power systems, as a raw material (feedstock) to produce chemicals, fertilizer and hydrogen and as lease and plant fuel. In 2020, the industrial sector accounted for about 33% of total U.S. natural gas consumption, and natural gas was the source of about 34% of the U.S. industrial sector’s total energy consumption.” In addition, the U.S. EIA includes the natural gas used to move product through pipelines as a fuel separately under its transportation category.
The cost of natural gas for electric power and for industrial heating processes is expected to rise as access to supplies is reduced. At the same time, emissions control regulations continue to grow more stringent. For these reasons there is an urgent need for industrial process and manufacturing companies to optimize and more tightly control heating processes that involve burners, boilers, furnaces, ovens, kilns, dryers, oxidizers and flare stacks. In addition, they must reduce their electric power costs.
Many process and plant engineers will be familiar with some form of the old adage, “You can’t control what you don’t measure accurately.” Fortunately, there are many process heating best practices that can be incorporated into industrial plant operations. The one thing all of these enhancements depend on, however, is accurate, consistent air/gas flow measurement to control the burn and ensure highly efficient heating.
These best practices not only help manufacturers become leaner by saving money but also allow them to become industry leaders in green, sustainable practices. With the U.S. Securities & Exchange Commission (SEC) recently announcing its consideration of a new climate emissions disclosure rule that would affect public companies, the U.S. could soon join many European countries already measuring and reporting their carbon footprints.
Fig. 2. The stoichiometric point in well-controlled natural-gas-fired processes is where the mixture of fuel to air is optimal. Shown here is the stoichiometric burn process.
Fig. 3. Natural gas composition differs somewhat around the world, as well as seasonally in very cold winters and hot, humid summer conditions.
Four Key Factors to Control the Burn
To reduce natural gas consumption, it is important that process and plant engineers know how to control the calorific value of their gas feed for any industrial heating process. To reach this goal, there are four key factors that engineers and technicians must consider when optimizing heating processes involving furnaces, ovens, kilns, dryers, heaters, etc.
#1. Process Stoichiometric Burn Ratio
The stoichiometric point in well-controlled natural-gas-fired processes is where the mix-ture of fuel to air is optimal. If there is too little air, the burner fire doesn’t achieve its full calorimetric heating potential and natural gas is wasted when it takes longer than necessary to achieve and sustain the required heating levels for vessel burners or steam boilers (Fig. 2).
When the fuel mixture is air-rich, there is the potential for excess nitrogen oxide (NOx) emissions. NOx is a highly reactive gas and a toxic pollutant that often appears as a brownish gas (remember smog?). It is a strong oxidizing agent and plays a major role in the atmospheric reactions with volatile organic compounds (VOCs) that produce ozone on hot summer days.
#2. Effects of Gas Composition
Natural gas composition (Fig. 3) differs somewhat around the world, as well as season-ally in very cold winter and hot, humid summer conditions. The primary energy components of natural gas are methane, ethane, propane, butane and condensates. The non-energy components are nitrogen, carbon dioxide, hydrogen sulfide and helium.
The mix of these components can affect gas density, the calorific value and, in turn, plant instrumentation. Very few flow technologies are fully immune or easily adaptable to changes in gas composition. A few volumetric flow technologies utilize a fixed-gas density at ambient conditions without taking into account pressures and temperatures that could affect mass flow readings. Some thermal flow instruments, however, are available with multiple calibration groups that can automatically switch seasonally or anytime inline gas analyzers indicate changes in the gas mixture to ensure the proper air/gas ratio is maintained for heating efficiency.
Fig. 4. In actual plant installations it is important to understand the potential full flow range of the gas to be measured, which is also known as turndown range.
#3. Process Variability – Turndown Range
Continuous and batch processes often operate at variable levels of production, which means the amount of natural gas and oxygen required for heating is also variable. Some of the reasons include processing multiple products on the same line, seasonal demand, wash-down cycles, seasonal planned maintenance, shift changes, etc.
For the most accurate gas and air flow measurement, a laboratory-like, steady-state flow is generally the easiest to measure. That’s why, in actual plant installations, it is important to understand the potential full-flow range of the gas to be measured (also known as turndown range) – from the lowest to highest flows – and if the flow measurement accuracy expected will be available over the entire flow range (Fig. 4).
#4. Flow-Meter Accuracy and Repeatability
In order to achieve the desired flow measurement accuracy level with confidence, the process or plant engineer must define the required process flow range, the desired flow measurement accuracy and the expected turndown ratio. For example, some processes require a rapid start-up with initial fast heating and then revert to a much lower steady-state or standby function in between batches. The speed of these changes in gas flow can affect measurement accuracy.
The major natural gas flow-meter technologies available (Coriolis, differential pressure, thermal, ultrasonic and vortex) all vary in specified accuracy from a high of ±0.01% or less, depending on their turndown ranges from 1,000:1 to 8:1 (and depending on sensing technology). For natural gas process or plant heating, thermal flow sensing offers the advantages of a broad flow range, wide turndowns and accuracy to ±0.75% (Fig. 5). With the exception of custody transfer applications, these instruments provide a great balance between total cost of ownership and performance.
Fig. 5. For natural gas processes or plant heating, thermal flow sensing offers the advantages of a broad flow range, wide turndowns and accuracy to ±0.75%.
Often Overlooked Considerations
Confusion often results because there are five different flow-sensing technologies that can all be used to measure natural gas or air. They all have their advantages and disadvantages, depending on the media composition, the process application and the point of measurement. For example, Coriolis, differential pressure (dP) and thermal flow-sensing technologies are all used to measure natural gas.
Coriolis meters, with their accuracy of ±0.01%, would seem to be the best performance choice for any application, but their much higher cost is typically best reserved for custody transfer applications where the higher cost is easily justified. Differential pressure, on the other hand, is a volumetric sensing technology typically used in liquids, which re-quires separate temperature and pressure compensation measurements to infer the mass flow rate of a gas.
In comparison, direct mass flow thermal-sensing technology places two thermowell-protected platinum RTD temperature sensors in the process stream. One RTD is heated while the other senses the actual process temperature. When using the constant-power method of driving the sensor, the temperature difference between the RTDs generates a voltage output, which is proportional to the media cooling effect for determining the gas mass flow rate (Fig. 6) without the extra pressure or temperature transmitters required by volumetric devices to account for changes in gas density.
When measuring air or gas, a thermal flow meter is typically the simplest and least complicated solution. In many cases, an insertion-type sensor can be used, which eliminates the need for costly bypasses required for servicing a spool-piece flow element. There are no additional sensors or other electronics to purchase, install or maintain, reducing the total installed and lifecycle cost of an instrumentation purchase decision. These qualities speed instrument return on investment (ROI) as well.
Fig. 6. When using the constant-power method of driving the sensor, the temperature difference between the RTDs generates a voltage output, which is proportional to the media cooling effect for determining the gas mass flow rate without extra pressure or temperature transmitters required by volumetric devices to account for changes in gas density.
When it comes to gas flow meters, it is important to ask the supplier about the type of calibration that will be performed. The industry relies on two standard calibration procedures: air-equivalency gas calibrations or laboratory gas calibrations performed under actual plant conditions. The equivalency method presumes that a substitute gas can be used in the calibration process. This methodology assumes that the thermo-physical properties of the substitute gas are similar to that of the actual gas to be measured, which is quite often not the case, especially when hydrocarbons and hydrogen are involved.
A laboratory calibration that mirrors actual plant conditions will provide the best results. These calibrations will take into account conditions that can include variable flows, high and low temperatures and multiple gas compositions (Fig. 7). The user is then presented with the calibration flow data recorded from the actual instrument calibration process, which provides assurance that the meter will operate accurately and dependably under installed field conditions.
Fig. 7. A laboratory calibration that mirrors actual plant conditions will provide the best results. These calibrations will take into account conditions that can include variable flows, high and low temperatures and multiple gas compositions
Installations with Limited Footprints
When planning to optimize an existing natural gas process line, an early consideration should be the optimal location of the flow instrument. Today’s legacy process and manufacturing plants are often a dense maze of piping, instruments and equipment that makes installing anything new a challenge. Flow meters installed to optimize natural gas heating processes are no exception.
All air/gas flow meters typically perform most accurately and consistently in a laboratory-like environment under a steady-state air/gas flow with no disturbances. In a real plant installation, they require a minimum upstream and downstream straight pipe run several diameters away from obstacles such as elbows, valves and blowers to achieve a disturbance-free, measurable and uniform flow profile. Without the required straight run, accurate and dependable flow measurement can be problematic, depending on the actual flow disturbances in the pipe.
To simplify meter installation in space-restricted areas of a plant, flow conditioners are available to tame unruly gas flows for proper measurement. For example, the FCI ST75 flow meter with optional integral Vortab Flow Conditioner (Fig. 8) solves these issues with uniform mixing tabs that actually straighten the gas flow prior to measurement.
For larger lines, spool or plate designs can be utilized with single-point thermal mass flow meters. It is important to pay attention to how the flow conditioner performs. Be sure to properly address swirling flow conditions from elbows out-of-plane that could affect measurement performance, and also look at permanent pressure loss for the type being used to avoid wasted energy costs.
Fig. 8. To simplify meter installation in space-restricted areas of a plant, flow conditioners are available to tame unruly gas flows for proper measurement. The FCI ST75 flow meter with optional integral Vortab Flow Conditioner solves these issues with uniform mixing tabs that straighten the gas flow prior to measurement.
With supply issues, rising prices and mandated carbon footprint measurement on the horizon, the question is not whether to optimize your plant’s natural gas processes but when is the right time to get better control of your burn. The higher gas prices go – whether because of supply, inflation or regulation – the faster the ROI payback will be. The bonus is that the modest cost of a flow-meter upgrade will better support the natural gas flow heating of your processes.
As you consider or plan the optimization of natural gas heating processes, you might want to consider the words of Rear Admiral Grace Murray Hopper: “The most dangerous phrase in the language is, ‘We’ve always done it that way.’”
For more information: Art Womack is Senior Application Engineer at Fluid Components International (www.fluidcomponents.com) in San Marcos, Calif. He can be reached at 760-744-6950.
- U.S. EIA Natural Gas Consumption, https://www.eia.gov/energyexplained/natural-gas/use-of-natural-gas.php
- Wall Street Journal, August 11, 2021, Page 1, 8, “Climate Accounting Looms for Companies”
Report Abusive Comment